PlymoVent OS 3 Vehicle Exhaust Extractor Removal System Blower Controller Hoses

Manufacturer: PlymoVent

Model: OS3

Condition: Used. This Vehicle Exhaust System is in good cosmetic condition with scuffs and scratches from regular industrial use and comes on non-original packaging.  We are unsure of the Hose Temperature Rating but because this came from a fire station we assume that they are at a minimum standard temperature (ST) if not High Temperature (HT).  The hoses are in good condition without any rips or tears.  The controller says that it is equipped to deal with a 3 HP 3 PH blower, but it is attached to and wired for a 1-1/2HP single-phase blower.  Some of the sections are currently attached with clamps while others are separated and the clamps are loose.  The Model Number on the Cincinnati Fan Label is very difficult to read and does not show well in the photograph.
The photos show the exact item(s) the buyer will receive.

Notes: We wired the controller and the blower motor to high voltage and observed the controller indicator lights turn on. The controller's manual run button was pushed, and the blower motor turned on and ran smoothly.  When the controller's stop button was pushed the blower motor turned off.  No additional testing was performed.
No manuals, cords/cables, or additional items are included if not listed or shown.

Included:

• (1) Plymovent Vehicle Exhaust Removal System Model OS3 Blower Operating System Controller
• (1) Baldor VL3513 1PH 115/208-230V 60Hz 1-1/2 HP Blower Motor w/ 6" Intake and Exhaust
• (1) Cincinnati Fan Model SPB-12 NIT 200-1 SN: 9806913 Blower Fan
• (1) 4" Dia 9' Length Yellow and Black Flexible Exhaust Hose w/ Stand and Connector Attachment Section at one end and a curved black attachment connector on the other.
• (1) 4" Dia 5-1/2' Length Yellow and Black Flexible Exhaust Hose Open on one end and a Safety Disconnect Handle on the other
• (1) 4" Dia 2' Length Yellow and Black Flexible Exhaust Hose w/ Safety Disconnect Male Connector on one end and a Magnetic Grabber attachment on the other
• (1) 6" Diameter 20" Length Black and Yellow Flexible Exhaust Hose (Attached to the Blower Intake)
• (1) 6" Diameter 59" Length Straight Galvanized Exhaust Pipe
• (2) 6" Diameter 11" Length Straight Galvanized Exhaust Pipe
• (1) 6" Diameter 18" Length Straight Galvanized Exhaust Pipe
• (1) 26-1/2" Straight Reducer from 6" Diameter to 4" Diameter Exhaust Pipe
• (1) 6" Diameter 22" Length Right Angle Galvanized Exhaust Pipe
• (1) 6" Diameter 8" Length 22 Degree Bend Galvanized Exhaust Pipe
• (1) 4" Diameter 8-1/2" Length Straight Galvanized Exhaust Pipe connected to 4" Diameter Straight Galvanized Pipe connected to a 4" Diameter 3" Length Straight Galvanized Exhaust Pipe w/ Stand on one side of the hose and a 4" Diameter 100 degree Bend Black Connector on the other.
• (5) 4" Diameter Clamps
• (5) 6" Diameter Clamps

Specifications:

• Manufacturer:  PlymoVent
• Model:  OS 3
• Description:  Complete Vehicle Exhaust System w/ Blower, Controller, and Hoses
  • Controller
    • Plymovent Vehicle Exhaust Removal System Model OS3 Blower Operating System Controller
      • The Control Panel is equipped with a companion fan motor starter contactor and overload relay specifically for the following fan motor
        • HP:  3
        • Voltage:  208
        • Phase:  3
        • Cycles:  60
        • Full Load Amps:  8
        • Ref PN or DWG. 706037
        • SN 5075786
  • Blower Motor
    • Baldor Industrial Motor
    • Single Phase
    • CAT. NO:  VL3513
    • SPEC.:  35C13-199
    • Frame:  56C
    • SER.:  F198
    • H.P.:  1-1/2 TE
    • Volts:  115/208-230
    • Amps:  15/7.9 - 7.5
    • RPM:  3450
    • Hz:  60
    • Class B
    • SER. F.:  1.15
    • DES:  L
    • P.F.:  82%
    • Rating:  400 AMB-CONT
    • 6" Dia. Blower Exhaust
    • 6" Dia Blower Intake
  • Fan
    • (1) Cincinnati Fan Model SPB-12 NIT 200-1 SN: 9806913 Blower Fan
  • Flexible Hoses
    • (1) 4" Dia 9' Length Yellow and Black Flexible Exhaust Hose w/ Stand and Connector Attachment Section at one end and a curved black attachment connector on the other.
    • (1) 4" Dia 5-1/2' Length Yellow and Black Flexible Exhaust Hose Open on one end and a Safety Disconnect Handle on the other
    • (1) 4" Dia 2' Length Yellow and Black Flexible Exhaust Hose w/ Safety Disconnect Male Connector on one end and a Magnetic Grabber attachment on the other
    • (1) 6" Dia 20" Length Black and Yellow Flexible Exhaust Hose (Attached to the Blower Intake)
  • Rigid Pip
    • (1) 6" Diameter 59" Length Straight Galvanized Exhaust Pipe
    • (2) 6" Diameter 11" Length Straight Galvanized Exhaust Pipe
    • (1) 6" Diameter 18" Length Straight Galvanized Exhaust Pipe
    • (1) 26-1/2" Straight Reducer from 6" Diameter to 4" Diameter Exhaust Pipe
    • (1) 6" Diameter 22" Length Right Angle Galvanized Exhaust Pipe
    • (1) 6" Diameter 8" Length 22 Degree Bend Galvanized Exhaust Pipe
    • (1) 4" Diameter 8-1/2" Length Straight Galvanized Exhaust Pipe connected to 4" Diameter Straight Galvanized Pipe connected to a 4" Diameter 3" Length Straign Galvanized Exhaust Pipe w/ Stand on one side of the hose and a 4" Diameter 100 degree Bend Black Connector on the other.
    • (5) A Total of 4" Diameter Clamps included
    • (5) A Total of 6" Diameter Clamps Included

30 Day Guarantee

• Guaranteed to be as described
• Can be returned for flaws or malfunctions that were not disclosed
• See complete terms

CDN Systems LLC, DBA Doug Deals, is not an authorized distributor or affiliated with the manufacturer of this product. Original manufacturer's warranty does not apply.